ASTM D5511 PDF

ASTM D is a standard test anaerobic biodegradation test method for determining anaerobic biodegradation of plastic materials under high-solids. ASTM D Standard Test Method. D Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under. High-Solids. ASTM D Significance and Use. Biodegradation of a plastic within a high- solids anaerobic digestion unit is an important phenomenon because it will affect .

Author: Moogujar Brajind
Country: Haiti
Language: English (Spanish)
Genre: Business
Published (Last): 27 October 2005
Pages: 88
PDF File Size: 17.32 Mb
ePub File Size: 12.51 Mb
ISBN: 686-1-23502-825-6
Downloads: 54258
Price: Free* [*Free Regsitration Required]
Uploader: Gardakree

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Note 1—This test method is equivalent to ISO However, it is expected to resemble the environment of a high-solids asym process operated under optimum conditions.

Specific hazards are given in Section 8. Work Item s – proposed revisions of this standard.

BioPro Global – ASTM D

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of adtm limitations prior to use. This procedure has been developed to permit the determination of the rate and degree of anaerobic biodegradability of plastic products when placed in a high-solids anaerobic digester for the production of digestate from municipal solid waste.

This d55111 contains methanogenic bacteria that are also found in landfills. Furthermore, results shall not be extrapolated past the actual duration of the test. Furthermore, results shall not be extrapolated past the actual duration of the test. This test method determines the degree and rate of biodegradation of plastic materials in an oxygen-free anaerobic environment.

Placing the sample materials in an inoculum derived from anaerobic digesters operating on household waste. Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test. The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste. Active view current version of standard. Historical Version s – view previous versions of standard.

Related Articles  SIEMENS SKD62 PDF

ASTM D5511 – Anaerobic Biodegradation

Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test. The testing process includes: Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test.

The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste.

x5511 Specific hazards are given in Section 8. Referenced Documents purchase separately The documents listed below are referenced satm the subject standard but are not provided as part of the standard. As these bacteria begin to utilize the carbon in the test samples, they produce carbonaceous gasses such as CO2 and CH4.

The molar weight of the total gas produced by the test samples is calculated and compared to the carbon weight of the original samples and the percent biodegradation of the samples can then be determined.

The vessels are airtight and are not exposed to UV radiation. The values given in SI units are to be regarded as the standard. Work Item s – proposed revisions of this standard. Link to Active This link will always route to the current Active version of the standard. When the test is run to satisfaction, final qstm and methane gas readings are recorded and the incubation vessels are emptied and the samples are cleaned and weighed.

Biodegradation of plastics could allow for the safe disposal of these plastics through aerobic and anaerobic solid-waste-treatment plants.

Three vessels are used for each sample, and one negative control and one positive control are prepared as well. These gasses are measured daily and the results are carefully recorded. Biodegradation of a plastic within a high-solids aatm digestion unit is an important phenomenon because it will affect the decomposition of other waste materials enclosed by the plastic and the resulting quality and appearance of the digestate after an anaerobic d5511 process.

Related Articles  FASHION SOURCE BOOK KATHRYN MCKELVEY PDF DOWNLOAD

Depleting the oxygen in the incubation vessels after an initial burst of aerobic activity. This is often sludge from a water treatment v5511 mixed with a certain percentage of solid material from composting facilities.

Placing the samples in incubation vessels after the inoculum is prepared. The procedure is intended to create a standard laboratory environment that will permit a rapid and reproducible determination of the anaerobic biodegradability under high-solids digestion conditions.

Furthermore, results shall not be extrapolated past the actual duration of the test.

ASTM D – Anaerobic Biodegradation | Situ Biosciences LLC

Link asstm Active This link will always route to the current Active version of the standard. They are kept within strict temperature and moisture tolerances. Asgm specifically, the procedure is intended to create a standard laboratory environment that will e5511 a rapid and reproducible determination of the anaerobic biodegradability under high-solids digestion conditions.

If the positive control which contains cellulose continues to exhibit biodegradation then the test is considered valid and the inoculum considered alive. The test is allowed to run for as long as desired. This test method also resembles other anaerobic conditions where the gas generated is recovered and biogas production is actively promoted by inoculation for example, codeposition of anaerobic sewage sludge, anaerobic leachate recirculationmoisture control for example, leachate recirculationand temperature control for example, short-term injection of oxygen, heating of recirculated leachate 5, 6, 7.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine asstm applicability of regulatory limitations prior to use. This test method is designed to be applicable to all plastic materials that are not inhibitory to the microorganisms present in anaerobic digesters operating on household waste.